This is a list of publishedThis list generally excludes draft versions. International Organization for Standardization (ISO) standards and other deliverables.ISO deliverables include "specifications" (ISO/PAS, ISO/TS), "reports" (ISO/TR), etc, which are not referred to by ISO as "standards". For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.
The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC 1) have been made freely and publicly available.
ISO 8000 – ISO 8999
ISO 8000 Data quality ISO 8002:1986 Mechanical vibrations – Land vehicles – Method for reporting measured data ISO 8015:2011 Geometrical product specifications (GPS) – Fundamentals – Concepts, principles and rules ISO 8041:2005 Human response to vibration - Measuring instrumentation ISO 8041-1:2017 Part 1: General purpose vibration meters ISO 8042:1988 Shock and vibration measurements – Characteristics to be specified for seismic pick-ups ISO 8044:2015 Corrosion of metals and alloys – Basic terms and definitions ISO 8048:1984 Technical drawings – Construction drawings – Representation of views, sections and cuts ISO 8049:2016 Ferronickel shot - Sampling for analysis ISO 8050:1988 Ferronickel ingots or pieces - Sampling for analysis ISO 8062 Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts ISO 8062-1:2007 Part 1: Vocabulary ISO/TS 8062-2:2013 Part 2: Rules ISO 8062-3:2007 Part 3: General dimensional and geometrical tolerances and machining allowances for castings ISO 8062-4:2017 Part 4: General tolerances for castings using profile tolerancing in a general datum system ISO 8063 Information processing – Data interchange on 6,30 mm (0.25 in) wide magnetic tape cartridge using IMFM recording at 252 ftpmm (6 400 ftpi) ISO 8063-1:1986 Part 1: Mechanical, physical and magnetic properties ISO 8063-2:1986 Part 2: Track format and method of recording for data interchange in start/stop mode ISO 8064:1985 Information processing – Reels for 12,7 mm (0,5 in) wide magnetic tapes – Sizes 16, 18 and 22 ISO/IEC 8072:1996 Information technology – Open systems interconnection – Transport service definition ISO/IEC 8073:1997 Information technology – Open Systems Interconnection – Protocol for providing the connection-mode transport service ISO 8088:1994 Equipment for olive cultivation and olive oil production – Vocabulary ISO 8090:1990 Cycles – Terminology ISO 8107:1993 Nuclear power plants - Maintainability - Terminology ISO 8109:1990 Banking and related financial services – Securities – Format of Eurobonds ISO 8114:1990 Textile machinery and accessories – Spindles for ring-spinning and doubling machines – List of equivalent terms ISO 8116 Textile machinery and accessories – Beams for winding ISO 8116-1:1995 Part 1: General vocabulary ISO 8119 Textile machinery and accessories – Needles for knitting machines – Terminology ISO 8119-1:1989 Part 1: Latch-type needles ISO 8119-2:1989 Part 2: Bearded needles ISO 8119-3:1992 Part 3: Compound needles ISO/IEC 81346: Industrial systems, installations and equipment and industrial products – structuring principles and reference designations ISO 8147:1995 Shipbuilding and marine structures – Derrick rigs and component parts – Vocabulary ISO 8152:1984 Earth-moving machinery – Operation and maintenance – Training of mechanics ISO 8153 Aerospace fluid systems and components – Vocabulary ISO 8153-1:2009 Part 1: Hose assemblies ISO 8157:2015 Fertilizers and soil conditioners – Vocabulary ISO 8159:1987 Textiles – Morphology of fibres and yarns – Vocabulary ISO 8160:1987 Textiles – Textured filament yarns – Vocabulary ISO 8178 Reciprocating internal combustion engines - Exhaust emission measurement ISO 8180 Ductile iron pipelines – Polyethylene sleeving for site application ISO 8199:2005 Water quality – General guidance on the enumeration of micro-organisms by culture ISO/IEC 8208:2000 Information technology – Data communications – X.25 Packet Layer Protocol for Data Terminal Equipment ISO/IEC 8211:1994 Information technology - Specification for a data descriptive file for information interchange ISO 8217:2017 Petroleum products - Fuels (class F) - Specifications of marine fuels ISO 8229:1991 Operations and baths relating to dry-cleaning machines – Vocabulary ISO 8277:2013 Ships and marine technology – Pipework and machinery – Information transfer ISO 8297:1994 Acoustics – Determination of sound power levels of multisource industrial plants for evaluation of sound pressure levels in the environment – Engineering method ISO 8316:1987 Measurement of liquid flow in closed conduits – Method by collection of the liquid in a volumetric tank ISO 8317:2015 Child-resistant packaging - Requirements and testing procedures for reclosable packages ISO 8319 Orthopaedic instruments – Drive connections ISO 8319-1:1996 Part 1: Keys for use with screws with hexagon socket heads ISO 8319-2:1986 Part 2: Screwdrivers for single slot head screws, screws with cruciate slot and cross-recessed head screws ISO/IEC 8326:1996 Information technology – Open Systems Interconnection – Session service definition ISO/IEC 8327 Information technology – Open Systems Interconnection – Connection-oriented Session protocol ISO/IEC 8327-1:1996 Protocol specification ISO/IEC 8327-2:1996 Protocol Implementation Conformance Statement (PICS) proforma ISO 8330:2014 Rubber and plastics hoses and hose assemblies - Vocabulary ISO 8333:1985 Liquid flow measurement in open channels by weirs and flumes – V-shaped broad-crested weirs ISO 8343:1985 Ferronickel - Determination of silicon content - Gravimetric method ISO/IEC 8348:2002 Information technology – Open Systems Interconnection – Network service definition ISO 8362 Injection containers and accessories ISO 8362-1:2009 Part 1: Injection vials made of glass tubing ISO 8362-2:2015 Part 2: Closures for injection vials ISO 8362-3:2001 Part 3: Aluminium caps for injection vials ISO 8362-4:2011 Part 4: Injection vials made of moulded glass ISO 8362-5:2016 Part 5: Freeze drying closures for injection vials ISO 8362-6:2010 Part 6: Caps made of aluminium-plastics combinations for injection vials ISO 8362-7:2006 Part 7: Injection caps made of aluminium-plastics combinations without overlapping plastics part ISO/TR 8363:1997 Measurement of liquid flow in open channels — General guidelines for selection of method [Withdrawn: replaced by ISO 18365] ISO 8368:1999 Hydrometric determinations – Flow measurements in open channels using structures – Guidelines for selection of structure ISO 8373:2012 Manipulating industrial robots – Vocabulary ISO 8378 Information processing – Data interchange on 130 mm (5.25 in) flexible disk cartridges using modified frequency modulation recording at 7 958 ftprad, 3,8 tpmm (96 tpi), on both sides ISO 8378-1:1986 Part 1: Dimensional, physical and magnetic characteristics ISO 8378-2:1986 Part 2: Track format A ISO 8378-3:1986 Part 3: Track format B ISO 8384:2000 Ships and marine technology – Dredgers – Vocabulary ISO 8388:1998 Knitted fabrics – Types – Vocabulary ISO 8421 Fire protection - Vocabulary ISO 8421-1:1987 Part 1: General terms and phenomena of fire ISO 8421-2:1987 Part 2: Structural fire protection ISO 8421-6:1987 Part 6: Evacuation and means of escape ISO 8421-7:1987 Part 7: Explosion detection and suppression means ISO 8422:2006 Sequential sampling plans for inspection by attributes ISO 8423:2008 Sequential sampling plans for inspection by variables for percent nonconforming (known standard deviation) ISO 8429:1986 Optics and optical instruments – Ophthalmology – Graduated dial scale ISO 8439:1990 Forms design - Basic layout ISO 8440:1986 Location of codes in trade documents ISO/IEC 8441 Information technology – High density digital recording (HDDR) ISO/IEC 8441-1:1991 Part 1: Unrecorded magnetic tape for (HDDR) applications ISO/IEC 8441-2:1991 Part 2: Guide for interchange practice ISO 8459:2009 Information and documentation - Bibliographic data element directory for use in data exchange and enquiry ISO 8462 Information processing – Data interchange on 6,30 mm (0.25 in) magnetic tape cartridge using GCR recording at 394 ftpmm (10 000 ftpi), 39 cpmm (1 000 cpi) ISO 8462-1:1986 Part 1: Mechanical, physical and magnetic properties ISO 8462-2:1986 Part 2: Streaming mode ISO/IEC 8473 Information technology – Protocol for providing the connectionless-mode network service ISO/IEC 8473-1:1998 Protocol specification ISO/IEC 8473-2:1996 Part 2: Provision of the underlying service by an ISO/IEC 8802 subnetwork ISO/IEC 8473-3:1995 Provision of the underlying service by an X.25 subnetwork ISO/IEC 8473-4:1995 Provision of the underlying service by a subnetwork that provides the OSI data link service ISO/IEC 8473-5:1997 Provision of the underlying service by ISDN circuit-switched B-channels ISO/IEC 8480:1995 Information technology – Telecommunications and information exchange between systems – DTE/DCE interface back-up control operation using ITU-T Recommendation V.24 interchange circuits ISO/IEC 8481:1996 Information technology – Telecommunications and information exchange between systems – DTE to DTE direct connections ISO/IEC 8482:1993 Information technology – Telecommunications and information exchange between systems – Twisted pair multipoint interconnections ISO/IEC 8484:2014 Information technology – Magnetic stripes on savingsbooks ISO 8485:1989 Programming languages - APL ISO 8498:1990 Woven fabrics – Description of defects – Vocabulary ISO 8499:2003 Knitted fabrics – Description of defects – Vocabulary ISO 8501 Preparation of steel substrates before application of paints and related products – Visual assessment of surface cleanliness ISO 8501-1:2007 Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings ISO 8501-2:1994 Part 2: Preparation grades of previously coated steel substrates after localized removal of previous coatings ISO 8501-3:2006 Part 3: Preparation grades of welds, edges and other areas with surface imperfections ISO 8501-4:2006 Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting ISO 8502 Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness ISO 8502-2:2017 Part 2: Laboratory determination of chloride on cleaned surfaces ISO 8502-3:2017 Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method) ISO 8502-4:2017 Part 4: Guidance on the estimation of the probability of condensation prior to paint application ISO 8502-5:1998 Part 5: Measurement of chloride on steel surfaces prepared for painting (ion detection tube method ISO 8502-6:2006 Part 6: Extraction of soluble contaminants for analysis - The Bresle method ISO 8502-9:1998 Part 9: Field method for the conductometric determination of water-soluble salts ISO 8502-11:2006 Part 11: Field method for the turbidimetric determination of water-soluble sulfate ISO 8503 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates ISO 8503-1:2012 Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces ISO 8503-2:2012 Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure ISO 8503-3:2012 Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile - Focusing microscope procedure