This is a list of publishedThis list generally excludes draft versions. International Organization for Standardization (ISO) standards and other deliverables.ISO deliverables include "specifications" (ISO/PAS, ISO/TS), "reports" (ISO/TR), etc, which are not referred to by ISO as "standards". For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.
The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC 1) have been made freely and publicly available.
ISO 2000 – ISO 2299 ISO 2000:2020 Rubber, raw natural — Guidelines for the specification of technically specified rubber (TSR) ISO 2002:1975 Raw styrene-butadiene rubber (SBR) — Determination of organic acid content [Withdrawn: replaced with ISO 7781] ISO 2003:1975 Raw styrene-butadiene rubber (SBR) — Determination of soap content [Withdrawn: replaced with ISO 7781] ISO 2004:2017 Natural rubber latex concentrate — Centrifuged or creamed, ammonia-preserved types — Specifications ISO 2005:2014 Rubber latex, natural, concentrate — Determination of sludge content ISO 2006 Rubber latex, synthetic — Determination of mechanical stability ISO 2006-1:2022 Part 1: High-speed method ISO 2006-1:2009 Part 2: Moderate-speed method under load ISO 2007:2018 Rubber, unvulcanized — Determination of plasticity — Rapid-plastimeter method ISO 2008:1987 Rubber latex, styrene-butadiene — Determination of volatile unsaturates [Withdrawn without replacement] ISO 2009:2011 Slotted countersunk flat head screws — Product grade A ISO 2010:2011 Slotted raised countersunk head screws — Product grade A ISO 2011 Nuclear energy — Vocabulary — second list [draft incorporated into ISO 921]Dimensional Co-ordination in Building Current Trends in ECE Countries; Report–Part 59 (1967). United Nations. Economic Commission for Europe. Committee on Housing, Building and Planning. pg. 84 ISO 2012:1976 Textile machinery and accessories — Cone sectional warping machines — Maximum usable width ISO 2013:1983 Textile machinery and accessories — Beams — Method of measuring variations of form and position [Withdrawn: replaced with ISO 8116-8] ISO 2014:1976 Writing of calendar dates in all-numeric form [Withdrawn: replaced by ISO 8601:1988] ISO 2015:1976 Numbering of weeks [Withdrawn: replaced by ISO 8601:1988] ISO 2016:1981 Capillary solder fittings for copper tubes — Assembly dimensions and tests ISO 2017 Mechanical vibration and shock – Resilient mounting systems ISO 2017-1:2005 Part 1: Technical information to be exchanged for the application of isolation systems ISO 2017-2:2007 Part 2: Technical information to be exchanged for the application of vibration isolation associated with railway systems ISO 2017-3:2015 Part 3: Technical information to be exchanged for application of vibration isolation to new buildings ISO 2020 Aerospace — Preformed flexible steel wire rope for aircraft controls ISO 2020-1:1997 Part 1: Dimensions and loads ISO 2020-2:1997 Part 2: Technical specification ISO 2021:1975 Data processing — Implementation of the ISO 8- bit coded character sets on punched cards [Withdrawn: replaced with ISO 6586] ISO/IEC 2022:1994 Information technology – Character code structure and extension techniques ISO 2023:1994 Rubber footwear — Lined industrial vulcanized-rubber boots — Specification [Withdrawn: replaced with ISO 20344] ISO 2024:1981 Rubber footwear, lined conducting — Specification [Withdrawn without replacement] ISO 2025:1972 Lined industrial rubber boots with general purpose oil resistance [Withdrawn without replacement] ISO 2026:2020 Aircraft — Connections for starting engines by air ISO 2027:1990 Natural rubber latex concentrate, evaporated, preserved — Specification ISO 2028:2015 Synthetic rubber latex — Preparation of dry polymer ISO 2030:2018 Granulated cork — Size analysis by mechanical sieving ISO 2031:2015 Granulated cork — Determination of apparent bulk density ISO 2032:1973 Heat-resisting equipment wires for aircraft ISO 2033:1983 Information processing – Coding of machine readable characters (MICR and OCR) ISO 2035:1974 Unplasticized polyvinyl chloride (PVC) moulded fittings for elastic sealing ring type joints for use under pressure — Pressure-resistance test [Withdrawn without replacement] ISO 2036:1976 Wood for manufacture of wood flooring — Symbols for marking according to species ISO 2037:1992 Stainless steel tubes for the food industry [Withdrawn without replacement] ISO 2039 Plastics — Determination of hardness ISO 2039-1:2001 Part 1: Ball indentation method ISO 2039-2:1987 Part 2: Rockwell hardness ISO 2040:1972 Strontium chromate pigments for paints ISO 2041:2009 Mechanical vibration, shock and condition monitoring – Vocabulary ISO 2042:1973 Aircraft electrical circuit diagrams ISO 2043:1974 Unplasticized polyvinyl chloride (PVC) moulded fittings for elastic sealing ring type joints for use under pressure — Oven test [Withdrawn: replaced with ISO 580] ISO 2044:1974 Unplasticized polyvinyl chloride (PVC) moulded solvent-welded socket fittings for use with pressure pipe — Hydraulic internal pressure test ISO 2045:1988 Single sockets for unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly (vinyl chloride) (PVC-C) pressure pipes with elastic sealing ring type joints — Minimum depths of engagement [Withdrawn: replaced with ISO 1452-(2,3)] ISO 2046:1973 Gaseous breathing oxygen supplies for aircraft ISO 2047:1975 Information processing – Graphical representations for the control characters of the 7- bit coded character set ISO 2048:1990 Double-socket fittings for unplasticized poly(vinyl chloride) (PVC-U) pressure pipes with elastic sealing ring type joints — Minimum depths of engagement [Withdrawn: replaced with ISO 1452-3] ISO 2049:1996 Petroleum products — Determination of colour (ASTM scale) ISO 2050:1976 Potassium chloride for industrial use — Determination of potassium content — Flame emission spectrophotometric method [Withdrawn without replacement] ISO 2051:1976 Potassium chloride for industrial use — Determination of potassium content — Potassium tetraphenylborate gravimetric method [Withdrawn without replacement] ISO 2052:1976 Potassium chloride for industrial use — Determination of potassium content — Sodium tetraphenylborate titrimetric method [Withdrawn without replacement] ISO 2053:1976 Potassium chloride for industrial use — Determination of moisture content — Gravimetric method [Withdrawn without replacement] ISO 2056:1976 Moulded polyvinyl chloride (PVC) pipes and fittings — Determination of Vicat softening temperature [Withdrawn: replaced with ISO 2507, now ISO 2507-(1-2)] ISO 2057:1981 Agricultural tractors — Remote control hydraulic cylinders for trailed implements ISO 2058:1973 Raw styrene butadiene rubber (SBR) — Determination of volatile matter [Withdrawn: replaced with ISO 248] ISO 2059: Concrete and reinforced concrete — notation [Rejected draft] ISO 2060:1994 Textiles — Yarn from packages — Determination of linear density (mass per unit length) by the skein method ISO 2061:2015 Textiles — Determination of twist in yarns — Direct counting method ISO 2062:2009 Textiles — Yarns from packages — Determination of single-end breaking force and elongation at break using constant rate of extension (CRE) tester ISO 2063 Thermal spraying — Zinc, aluminium and their alloys ISO 2063-1:2019 Part 1: Design considerations and quality requirements for corrosion protection systems ISO 2063-2:2017 Part 2: Execution of corrosion protection systems ISO 2064:1996 Metallic and other inorganic coatings — Definitions and conventions concerning the measurement of thickness ISO 2065:1972 Textile machinery and accessories — Cylindrical tubes for tape yarns [Withdrawn: replaced with ISO 3914-3] ISO 2066:2004 Resilient floor coverings — Determination of moisture content of agglomerated composition cork ISO 2067:2019 Granulated cork, broken cork and crushed cork — Sampling for the determination of moisture content ISO 2068:1972 Barium chromate pigments for paints ISO 2069:1976 Aluminium oxide primarily used for the production of aluminium — Determination of calcium content — Flame atomic absorption method [Withdrawn without replacement] ISO 2070:1997 Aluminium oxide primarily used for the production of aluminium — Determination of calcium content [Withdrawn without replacement] ISO 2071:1976 Aluminium oxide primarily used for the production of aluminium — Determination of zinc content — Flame atomic absorption method [Withdrawn without replacement] ISO 2072:1981 Aluminium oxide primarily used for the production of aluminium — Determination of zinc content — PAN photometric method [Withdrawn without replacement] ISO 2073:1976 Aluminium oxide primarily used for the production of aluminium — Preparation of solution for analysis — Method by hydrochloric acid attack under pressure [Withdrawn without replacement] ISO 2074:2007 Plywood – Vocabulary ISO 2075:1972 Cutting netting to shape — Determination of the cutting rate [Withdrawn without replacement] ISO 2076:2021 Textiles – Man-made fibres – Generic names ISO 2077:1979 Pure expanded corkboard — Determination of the modulus of rupture by bending [Withdrawn without replacement] ISO 2078:1993 Textile glass — Yarns — Designation ISO 2079:1981 Surface treatment and metallic coatings — General classification of terms [Withdrawn: replaced with ISO 2080] ISO 2080:2022 Metallic and other inorganic coatings – Surface treatment, metallic and other inorganic coatings – Vocabulary ISO 2081:2018 Metallic and other inorganic coatings — Electroplated coatings of zinc with supplementary treatments on iron or steel ISO 2082:2017 Metallic and other inorganic coatings — Electroplated coatings of cadmium with supplementary treatments on iron or steel ISO 2083:1973 Gasoline — Determination of lead content — Volumetric chromate method [Withdrawn without replacement] ISO 2084:1974 Pipeline flanges for general use — Metric series — Mating dimensions [Withdrawn: replaced with ISO 7005-(1-3)] ISO 2085:2018 Anodizing of aluminium and its alloys — Check for continuity of thin anodic oxidation coatings — Copper sulfate test ISO/R 2091:1971 Hydraulic cylinders — Internal diameters and piston rod diameters — Metric series [Withdrawn without replacement] ISO 2092:1981 Light metals and their alloys — Code of designation based on chemical symbols [Withdrawn without replacement] ISO 2093:1986 Electroplated coatings of tin — Specification and test methods ISO 2094:1999 Textile floor coverings — Determination of thickness loss under dynamic loading ISO 2095:1977 Textile floor coverings — Determination of mass of effective pile per unit area that can be shorn away from the substrate [Withdrawn: replaced with ISO 8543] ISO 2096:1972 Glycerols for industrial use — Methods of sampling ISO 2097:1972 Glycerols for industrial use — Determination of water content — Karl Fischer method [Withdrawn without replacement] ISO 2098:1972 Glycerols for industrial use — Determination of ash — Gravimetric method [Withdrawn without replacement] ISO 2099:1972 Purified glycerol for industrial use — Determination of density at 20 degrees C [Withdrawn without replacement] ISO 2100:1987 Aircraft — Electrical connectors — Tests ISO/R 2101:1971 Aluminium and aluminium alloys — Shear test for rivet wire and rivets [Withdrawn without replacement] ISO 2103:1986 Loads due to use and occupancy in residential and public buildings [Withdrawn without replacement] ISO/R 2105:1971 Textile machinery and accessories — Tubes for draw-winders for man-made fibres [Withdrawn: replaced with ISO 3914-3] ISO 2106:2019 Anodizing of aluminium and its alloys — Determination of mass per unit area (surface density) of anodic oxidation coatings — Gravimetric method