In the U.S. Army Coast Artillery Corps, the term fire control system was used to refer to the personnel, facilities, technology and procedures that were used to observe designated targets, estimate their positions, calculate firing data for guns directed to hit those targets, and assess the effectiveness of such fire, making corrections where necessary.
Fire control instruments The Coast Artillery's early fire control instruments supported optical rangefinding and position finding, either horizontal base or vertical base, with both systems usually present for each fort. Early horizontal base rangefinding required two azimuth (a.k.a. bearing or deflection) instruments, preferably widely separated, and a communications system to transmit data to a plotting room and then to the guns. The instruments were often in bunkers called base end stations, as they defined the endpoints of a baseline. A base end station might be a two-story structure with a plotting room or other instruments or facilities on the lower level. By the 1920s coincidence range finders, self-contained horizontal base instruments, were in use along with the other methods. Though these could be used quickly, these had baselines of only a few feet, reducing their accuracy and maximum effective range.
Vertical base rangefinding used a single depression position finder (DPF) mounted as high as possible above the water level; these were derived from similar British devices and adopted beginning in 1896. Along with the target's azimuth, they measured the vertical angle from the instrument to the target; with the instrument's height above water known, this determined the target's range. The need to be progressively higher above water as gun ranges increased was a severely limiting factor for the DPF, and they were usually supplemented by horizontal base systems. As gun ranges continued to increase, in the 1920s additional horizontal and vertical base systems were installed, in tall fire control towers at some locations, including the Harbor Defenses of Portsmouth (New Hampshire) and the Harbor Defenses of the Delaware.Berhow, pp. 283–290
By World War II, radar had become a better method of determining a target's position. However, in the bombardment of Fort Stevens by a Japanese submarine on 21 June 1942, the only time a coastal defense installation in the contiguous United States was attacked, the fort's commander used a DPF to determine that the submarine was out of range, and thus did not return fire.
Plotting rooms Plotting rooms were used by the Coast Artillery Corps to house a team of soldiers who were engaged in controlling fire for the guns of a coastal artillery battery. Plotting rooms were in use from about 1895 through the end of WWII, at which point the U.S. Coast Artillery was disbanded. In some newer Coast Artillery batteries during World War II, these rooms were called Plotting, Switchboard, and Radio (PSR) rooms, and were often (but not always) integrated with the bunkers at the battery that were also used for ammunition storage, electrical generators, and other support functions. For 16-inch guns, the PSR bunker was some distance from the gun battery bunker, to avoid the shock of firing interfering with the plotting room equipment.
A plotting room was connected by telephone lines (and sometimes by radio) to base end stations that observed the locations of enemy ships and sent data to plotting room soldiers who used equipment such as plotting boards to calculate where the guns should be pointed and when they should be fired. Telephone lines also ran from the plotting room to the guns and were used to relay firing data. Other devices, like "range correction boards" or "deflection boards", were used in the plotting room to calculate corrected firing data (described below) or to adjust range and azimuth after spotters in remote observing stations observed where prior shots had fallen.FM 4-15
Plotting rooms were sometimes made of concrete and buried below ground (for protection) or were located in the reinforced concrete casemates of coast artillery batteries. Plotting rooms were also located in free-standing structures, either low towers or one- or two-story wood and plaster buildings, which might house facilities for several batteries near each other in barracks-like structures. These multiple-battery installations might also have sleeping quarters and latrine facilities nearby. Sometimes plotting rooms were located hundreds of yards from the batteries they controlled. They often sat on top of nearby hills or ridge lines.
Gun data computers were electro-mechanical computers were introduced into the Coast Artillery in the 1940s, particularly in the new 100- and 200-series 16-inch and 6-inch gun batteries that became operational during that period. Some of these computers received data directly from communicators that were connected to observation instruments in fire control stations or from Coast Artillery radar equipment.Gun Data Computers, Coast Artillery Journal March–April 1946, pp. 45–47
Basic fire control procedure In brief, the fire control system in use from about 1900 through WW2 involved observers, often situated in base end stations or other fire control towers, using optical instruments (like azimuth telescopes or depression position finders) to measure bearings and/or ranges to targets (usually moving ships). Both horizontal and vertical base rangefinding systems were used.Bolling W. Smith, "Vertical and Horizontal-Base Position Finding Systems," The Coast Defense Study Group Journal, Vol. 13, Issue 3, August, 1999. These observations were communicated to personnel in battery plotting rooms, who used a mechanical device called a plotting board to indicate the target's observed location on a map of the area. The red "1" on the diagram at right indicates this first stage of the fire control process.
Once several positions had been plotted for the target (blue circles on Figure 1 at left), plotting board operators estimated the position of the target at the instant a salvo, fired by the battery, was expected to land. This position was called the "set forward point" (green square in Figure 1), since it involved "setting forward" the target's expected position (assuming continued forward travel at the same speed and in the same direction) during two intervals of time: (1) the "dead time" between the time the observation had been made and the time the guns were actually fired at that target plus (2) the "time of flight"--the time the projectile spent in the air before hitting the target. The set forward point was expressed in terms of firing data: a range (in yards) and an azimuth (a compass heading in degrees) at which the gun(s) should be pointed by the gun crews in order to hit the target.
Before these firing data were sent to the guns, however, they were corrected for a variety of "non-standard conditions", like temperature (which affected the explosive power of the powder charge) or wind strength and direction (which affected the flight of the projectile). The red "2" in the diagram at right indicates this stage in the fire control process. Special devices, like the "deflection board" (for corrections in azimuth) or the "range correction board" (for corrections in range) were used to produce corrected firing data (described below).Coast Artillery Journal index at sill-www.army.mil
The final stage (the red "3" in the diagram at right) had to do with using feedback from the battery's observers, who spotted the fall of the projectiles (over or under range, left or right in azimuth, or on target) and telephoned their data to the plotting room so that the aim of the guns could be corrected for future salvos."Seacoast Artillery Firing," Coast Artillery Journal, Vol. 63, No. 4, October, 1925, pp. 375–391
Fire control timing
Fire control in the Coast Artillery involved a sequence of steps that was carried out over and over again while a target was being tracked and fired upon. First, observers sighted on the target and sent their observations to the plotting room. Next, plotters calculated the target's position and probable future movement, as well as adjustments to range and azimuth (direction). Then firing data were sent to the batteries and used by gun crews to point their guns. The guns were fired. Finally, spotters might spot the fall of the projectiles, sending this information back to the plotting room for use in correcting fire. After this, observers would sight on the (new) position of the target, beginning another cycle. The time period between sequential sightings by the observers was called the "observing interval".FM 4-15, Ch. 6 It was typically set at 20 seconds for controlling batteries of guns larger than 3-inch caliber.
Not only did everyone in the fire control system have to stay in synch (for example, knowing which one of a series of sets of fire control data they were working with at any given time) but certain functions (notably the making of target sightings by the observers and the firing of the guns by the gun crews) had to be carried out at precise intervals if the accuracy of the system was to be maintained.
To enable all battery personnel to stay in synch, a "time interval bell" (or buzzer) would be rung in every observation or spotting station serving the battery, in the plotting room, and at each gun, using bells or buzzers wired together with a centrally located master clock.Bolling W. Smith, "WW-II Time Interval Systems," The Coast Defense Study Group Journal, Vol. 10, May 1966, p. 76 Five seconds before the start of the next cycle, the bell would ring. After a one-second delay, it would ring again. And after another one-second gap the bell would ring a third time, and on this third ring the observations were made again and/or the guns were fired.
A well-trained battery could observe, plot, adjust, and transmit the firing data to its guns, which could then be loaded and laid, all before the next 20-second bell, at which point the guns would be fired. If for some reason the firing data were not received in time by the guns, or if a hold-up or a misfire occurred, then firing happened at the end of the following interval. In such a case, the command "Relay!" (re-lay) was given at the guns.
Corrected firing data Corrected firing data was a term used in the Coast Artillery Corps for fire control purposes circa 1890–1945. It refers to firing data (range and azimuth (a.k.a. bearing or deflection) to the target) that had been corrected for various "non-standard conditions". In Coast Artillery parlance, the term "correction" usually referred to changes in estimated range or deflection (direction) that were made prior to firing. The term "adjustment" usually referred to changes that were made after a shot had been fired and were used to modify the aim of the gun(s) for the next shot. Adjustments were usually made by observing and plotting the fall (splashes) of the shells fired and reporting by how much they were left or right in azimuth or over or under in range.FM 4-15, Ch. 4
Factors influencing corrections Corrections could be made for the following factors: Variations in muzzle velocity (including the results of variations in temperature of powder) Variations in atmospheric density Variations in atmospheric temperature Height of site (taking account of the level of the tide) Variations in weight of projectile Travel of the target during the time of the projectile's flight Wind Rotation of the earth (for long range guns) Drift
The uncorrected firing data, to which such corrections were applied, were those derived, for instance, from using a plotting board to track the position of an observed target (e.g., a ship) and the range and azimuth to that target from the guns of a battery.
Implementing corrections
Meteorological data