IOIO (pronounced yo-yo) is a series of open source PIC microcontroller-based boards that allow Android mobile applications to interact with external electronics.SparkFun Hosts Android Development Class with IOIO, PRNewsWire, BOULDER, Colo., June 27, 2012 The device was invented by Ytai Ben-Tsvi in 2011, and was first manufactured by SparkFun Electronics.IOIO Wiki, GitHub, "And this is the blog of Ytai, the inventor of IOIO"Ytai Ben-Tsvi's Blog, BlogspotIOIO for Android, DEV-10585, SparkFun The name "IOIO" is inspired by the function of the device, which enables applications to receive external input ("I") and produce external output ("O").
Features The IOIO board contains a single PIC MCU that acts as a USB host/USB slave and communicates with an Android app running on a connected Android device. The board provides connectivity via USB, USB-OTG or Bluetooth, and is controllable from within an Android application using the Java API.IOIO-OTG, DEV-12633, SparkFunIOIO-OTG Beginners Guide, SparkFunIOIO Java Library Basics, GitHub
In addition to basic digital input/output and analog input, the IOIO library also handles PWM, I2C, SPI, UART, Input capture, Capacitive sensing and advanced motor control. To connect to older Android devices that use USB 2.0 in slave mode, newer IOIO models use USB On-The-Go to act as a host for such devices. Some models also support the Google Open Accessory USB protocol.
The IOIO motor control API can drive up to 9 motors and any number of binary actuators in synchronization and cycle-accurate precision.Motor control, IOIO WikiIOIO Plotter and the Motor Control Library, MAY 14, 2013, Ytai Ben-Tsvi Blog Developers may send a sequence of high-level commands to the IOIO, which performs the low-level waveform generation on-chip. The IOIO firmware supports 3 different kinds of motors; stepper motors, DC motors and servo motors.
Device firmware may be updated on-site by the user. For first-generation devices updating is performed using an Android device and the IOIO Manager application available on Google Play.IOIO Manager, Google Play Store Second-generation IOIO-OTG devices must be updated using a desktop computer running the IOIODude application.IOIO-OTG Bootloader and IOIODude, IOIO Wiki
The IOIO supports both computers and Android devices as first-class hosts, and provides the exact API on both types of devices. First-generation devices can only communicate with PCs over Bluetooth, while IOIO-OTG devices can use either Bluetooth or USB. PC applications may use APIs for Java or C# to communicate with the board; Java being the official API.IOIODotNet, GitHub
Applications The IOIO hardware and software is entirely open source,IOIO, GitHub and enabled the creation of hundreds of DIY robotic projects around the world.Projects built with IOIO, PinterestDIY Android-powered tank, Edwin Kee, 08/10/2011, UbergeekDIY smartphone thermostat has us wondering what happened to Android@Home, 15 Oct 2012, Kevin Krause, PhandroidBreathing on the IOIO board for an Android Breathalyser, GadgetMaster, Electronics Weekly, 11 May 2012
The board has been featured in various learning kits, which aim to help students write Android applications that can interact with the external world.IOIO Mint - Portable Android Development Kit, AdaFruitIOIO Inventor's Kit, RB-Spa-934 , RobotShopSparkFun Inventor's Kit for IOIO, SparkFun
The Qualcomm Snapdragon Micro Rover is a 3D printed robot that leverages an Android smartphone and the IOIO to control the robot's motors and sensors.Snapdragon Micro Rover, Qualcomm A team led by Israeli inventor Dr. Guy Hoffman created an emotionally-sensitive robot, that relies on the IOIO to control the robot's hardware.
Reviews The IOIO has been variously described as a "geek's paradise", "an easy way to get I/O from an Android device’s USB connection" and "a USB I/O breakout board for Android smartphones which turns your handset into a super-Arduino of sorts".SparkFun IOIO for Android makes Arduino-style hacks simple, Android Community, April 7, 2011, Chris DaviesIOIO for Android detailed: Project samples from USB breakout board, Android Community, April 8, 2011, Chris Davies It featured as a recommended "gift for geeks" in a Scientific Computing article.
According to SlashGear, an online electronics magazine:
According to SparkFun, the first manufacturer of the device:
According to Ytai Ben-Tsvi, the inventor of the device:
Technical details
IOIO V1
The first-generation IOIO boards (known as IOIO V1) contain the following on-board features:Getting To Know The IOIO-V1 Board, IOIO WikiIOIO V1, SparkFun USA This generation only supports USB slave mode, and requires a USB master as the host (PC or newer Android phones).
The IOIO V1 is a 3.3 V logic level device, and features a 5 V DC/DC switching regulator and a 3.3V linear regulator. The 5 V regulator supports a 5–15 V input range and up to 1.5 A load. This facilitates charging a connected Android device as well as driving several small motors or similar loads.
Feature Details Description USB connector type A, female Used to connect to the Android device. GND pins 9 pins Ground connection. VIN pins 3 pins Used for power supply to the board. Voltage between 5 and 15 V should be supplied. 5 V pins 3 pins Normally used as 5 V output to user electronics, when the board is powered from VIN. Can be used as 5V input in case VIN is not connected. 3.3 V pins 3 pins 3.3 V output to user electronics. I/O pins 48 pins General purpose I/O pins. Some have special functions, such as ADC, Input Capture, UART, PWM, Comparator or for programming the PIC MCU (ICSP). Power LED Lights when the IOIO is getting power. Stat LED Lights briefly during power-up and then becomes under application control. MCLR pin Not normally used. Its purpose is for programming new bootloader firmware on the IOIO board. Charge current trimmer (CHG) Adjusts the amount of charge current supplied on the VBUS line of the USB to the Android device. Turning in the (+) direction increases charge current.
IOIO OTG
The second-generation IOIO boards (known as IOIO-OTG) contain the following on-board features: Getting To Know The IOIO-OTG Board, IOIO WikiIOIO OTG, SparkFun USAIOIO OTG, SparkFun USA As the name suggests, a key feature of this generation is the introduction of USB-OTG, supporting USB master or slave mode. This enables the IOIO to connect to older Android phones that only support USB slave mode, in addition.
The IOIO-OTG is a 3.3 V logic level device, with some of the pins being 5 V tolerant. It features a 5 V DC/DC switching regulator and a 3.3 V linear regulator. The 5 V regulator supports a 5–15 V input range and up to 3 A load. This facilitates charging a connected Android device as well as driving several small motors or similar loads.
Feature Details Description USB connector micro-AB, female Used to connect to host computer, an Android device or a Bluetooth dongle. Power jack 2-pin JST, female Used for power supply to the board. Voltage between 5–15 V should be supplied. GND pins 10 pins Ground connection. VIN pins 3 pins Used for outputting the supply voltage to your circuit, or as an alternative input to the power jack. 5V pins 3 pins 5V output from the on-board regulator, which can be used in your circuit. 3.3 V pins 3 pins 3.3 V from the on-board regulator, which can be used in your circuit. I/O pins 46 pins General purpose I/O pins. Some have special functions, such as ADC, Input Capture, UART, PWM, Comparator or for programming the PIC MCU (ICSP). PWR LED red Lights when the IOIO is getting power. STAT LED yellow General purpose on-board LED, under application control. MCLR pin Not normally used. Its purpose is for programming new bootloader firmware on the IOIO board. BOOT pin Special pin used for getting the IOIO into bootloader mode on power-up. Note that this pin is shared with the stat LED. Charge current trimmer (CHG) Adjusts the amount of current supplied on the VBUS line of the USB when acting as a USB host. Typically used in battery-powered application with Android to prevent the Android from draining the battery quickly. Turning in the (+) direction increases charge current. Host switch In "A" mode, the IOIO-OTG will detect whether it should act as host or as device automatically, according to whichever USB connector is plugged in (micro-A or micro-B). To support non-standard USB cables or adapters that use micro-B type, move the switch to the "H" position to force host mode.
See also Arduino BeagleBoard Raspberry Pi PICkit Open-source robotics PIC microcontroller
References